Invidia RH vs. CRSX RH?

[TRQLESS]

Originally Posted by 20rsxs04

why you laughing?

but on another note, I ended up going with invidia RH and matched with my Q300.
I LOVE the combo the only compaint i have it the rattle that im going to have to fix.
One is under the shifter the mid pipe is to close to the bottom of the car and if down shifting under heavy load it smacks the bottom of the car and the other is the muffler hanger on the passenger side when i hit bumps and what not hit the trunk floor.

but the RH is AMAZING, no compaint there!

Sounds like you need a set of energy suspension motor mount inserts. That will fix it from hitting anything. Your motor is moving too much and will break your exhaust/downpipe. They are about $30 and worth every bit.

[Furbyj1]

^ motor mounts gotta be really bad for the motor to move around that much

[20rsxs04]

yah idk i mean where it is hitting it like maybe an inch away from the bottom of the car so id say any wiggle at all is gonna make it hit i just need a way to get it farther away or something to put in between

[TRQLESS]

Originally Posted by 20rsxs04

yah idk i mean where it is hitting it like maybe an inch away from the bottom of the car so id say any wiggle at all is gonna make it hit i just need a way to get it farther away or something to put in between

I gave you the solution for the problem.

[20rsxs04]

Originally Posted by TRQLESS

I gave you the solution for the problem.

would full motor mounts work too?

[Jack Bauer]

Originally Posted by 20rsxs04

would full motor mounts work too?

Yes.

[ohsnapzitzmeng]

strup rh... end of story

[mikeybaby]

does the invidia race header bolt right up to the 05? or does it require modifacations

[145mph]

It bolts right up .

[145mph]

What sway bar are people using with the invidia header ? The header was rubbing against the stock sway a little in my boy 06 type s . Or should he get motor mounts/ inserts and leave the stock sway

[02civic629]

id deff get motor mount inserts asap because all that jumping around with the header could cause it to snap, and just get both, dont be cheap, get a civic em2 front sway for clearance issues and get mount inserts asap

[145mph]

Originally Posted by 02civic629

id deff get motor mount inserts asap because all that jumping around with the header could cause it to snap, and just get both, dont be cheap, get a civic em2 front sway for clearance issues and get mount inserts asap

The em2 he got didn't fit properly for some reason ...what other sway will work ?

[mikeybaby]

im having that same problem with the rattle now that I have both the invidia race header and the q300 exhaust you think that motor mount inserts would really solve that problem? because its the way the exhaust sits its always like you have to heat up the hangers and bend them down a little bit no?

[brutalityrr1]

I use the ep3 sway bar clears just fine and bought it from crsx

[145mph]

I thought the em2 and the ep3 had the same stock front sway bar

[Mr.Type-S]

Originally Posted by mikeybaby

im having that same problem with the rattle now that I have both the invidia race header and the q300 exhaust you think that motor mount inserts would really solve that problem? because its the way the exhaust sits its always like you have to heat up the hangers and bend them down a little bit no?

i have same setup with invida RH and q300 cat back i also have front and rear ES inserts and it still rattles on idle, pisses me off . hope i can find a fix for this next time i get it up on the lift.

[20rsxs04]

Originally Posted by Mr.Type-S

i have same setup with invida RH and q300 cat back i also have front and rear ES inserts and it still rattles on idle, pisses me off . hope i can find a fix for this next time i get it up on the lift.

where is your rattle at? is it the rear passenger hanger for the muffler? if so its hitting the body underneath and i bet it can be fixed with some rubber tubing cut long ways and zip tied on thats what i am about to do any way.

As far as a sway bar goes i have a progress front non adjustable and it seems to be doing fine for me and it was pretty cheap but my header is also rapped so i probably wouldn't hear it any way haha.

[ubreak_ubuy]

Originally Posted by 145mph

The em2 he got didn't fit properly for some reason ...what other sway will work ?

currently having the same problem with my invidia rh. bought the em2 front sway bar and it doesnt clear the rh. had to go back with the stock 06 front sway but it touching the header and pushing the sway bar against the chassis. im about to purchase the progress bar but not sure if this will fix the issue. anyone have any pics to compare the progress front sway bar against the 05-06 oem front sway bar?