Comptech Supercharger FAQ - Club RSX Message Board
Go Back   Club RSX Message Board > PERFORMANCE BASICS RSX > Supercharging RSX
Use the same user name on Club RSX, Club EP3, and Club ILX!

Reply
 
Thread Tools
Old 04-26-2005, 01:15 PM   #1
conradb212
ECU Tuner
 
conradb212's Avatar
 
Join Date: Nov 2003
Location: Farragut, TN
Posts: 4,281
iTrader: (0)
conradb212 is an unknown quantity on c-rsx
Comptech Supercharger FAQ

What is the Comptech Supercharger?

It is a Roots-type supercharger kit for the Acura RSX Type-S. The kit contains the compressor, manifold, pulleys, tensioners, assorted hardware and a k-100 upgrade to your ECU. Click here to see what the CTSC looks like.

Who is Comptech? Do they know what they're doing?

Comptech is probably as close to a factory-sponsored performance shop as Acura and Honda have. For over 20 years Comptech has been building and racing Honda performance products, including Indy 500 race cars. Comptech is located in El Dorado Hills, California. They make supercharger kits for many Honda and Acura lines.

How much does the kit cost?

US$3,595 for the base kit including the k-100 ECU upgrade and flash. Different pricing is available for those who already have the K-Pro.

What performance gains will I get?

The base CTSC kit will add between 40 and 50 wheel horsepower, depending whether your start from stock or already have some modifications. My car, which already had a street header, CAI, catback and K-Pro went from 192 to 232. Overall, people who install the base kit report anywhere between 225 and 235 whp. Click here to see dyno comparison stock NA to street CTSC.

Is the CTSC kit street legal?

The base kit has received CARB approval and is therefore completely street-legal anywhere. CARB generally requires that no emissions-related items have been changed, and that consumers cannot change settings. This is why the street CTSC kit uses the stock 310cc fuel injectors and the k-100 ECU upgrade (unlike the K-Pro, the k-100 cannot be tuned by users).



Will my gas mileage go down with the CTSC?

Very little. My car had a lifetime average of 26.5 miles per gallon (over 10,000 miles). With the base CTSC kit, mileage decreased by just over one mile per gallon to 25.5 mpg. As always, mileage varies depending on how often you're boosting.

Will there be additional stress on my car?

Any performance mod adds stress. However, the CTSC system has a bypass valve that cuts out the compressor when no boost is required, which means that 95-98% of the time you're not boosting and not adding stress to the engine. The compressor uses less than 1/3 of 1 hp when cruising at 60 mph.

How does this bypass valve work?

It is a butterfly valve like the one in the throttle body (see picture). The default is closed. When vacuum is high (idle-cruising) an actuator opens the bypass valve so that intake air bypasses the compressor. When accelerating, vacuum decreases and the bypass valve instantly closes. Intake air now goes through the compressor, building boost.

I thought a supercharger needs larger injectors.

More power means more fuel means larger injectors. However, in order to pass CARB, the base kit had to use the stock injectors. They run out of capacity at between 7100 and 7500 rpm. This is why the CTSC base kit has a 7900 rpm redline. Extensive datalogs have shown that even though the injectors are at 100% dutycycle, the air-fuel ratio remains within normal range even at redline.

What's the deal with larger injectors, anyway?

Unfortunately, almost every car company uses different injector plugs. The most common third party injectors for the K-Series, RC Engineering injectors, have a different plug and need adapter clips soldered on. Comptech does not want to cut the wires and solder on adapters. Power Enterprises makes 510cc injectors that fit, but they are expensive. Comptech has been experimenting with less expensive alternatives. They tested 470cc Marelli injectors that could be used with a small alteration to the connector. They also tested modified stock injectors and other modified Honda injectors that can flow up to 530cc (stock is 310cc). Bottomline: if you use K-Pro and install your own pulleys and injectors, you can use anything you want. If you want official upgrades from Comptech, they will likely have a solution that costs less and is plug-and-play.

Can I install the kit myself?

You can, but I do not recommend it and Comptech does not recommend it. There is very little room to work with, and it is crucial to get pulleys and tensioners done just right. It's better to pay a qualified installler. That way, if something goes wrong, you can go back and have it fixed.

What does the CTSC sound like?

It's pretty quiet. Much quieter, actually, than a NA card with a SRI or CAI. Even if you have a SRI or CAI, the compressor will muffle the sound. What you hear when you step on it is an urgent, mechanical whine as you accelerate.

How much boost does the CTSC make?

The base kit makes up to just under 5 psi of boost. The "Stage 2" upgrade increases boost by using a smaller compressor pulley to make the compressor turn faster. The base kit uses a 3.8-inch pulley. Stage 2 uses a 3.6-inch pulley which increases boost to about 6 psi. Comptech also has 3.3-inch (about 8 psi) and 3.1-inch pulleys (about 10 psi).

230 whp is nice, but I want more!

Then you need to get larger injectors and a smaller blower pulley. Comptech's "Stage 2" upgrade consists of a reflash, a 3.6-inch pulley, and a new set of injectors that flows about 530cc. In my car, that combination makes 258 whp, with the cat in place. Comptech does not want to solder or crimp injector wires and the Stage 2 injectors are drop-in replacements for the Honda stock injectors. Click here to see dyno comparison between CTSC base and Stage 2.

If you have the K-Pro, you can do your own "Stage 2" (or better) by buying the 3.6 or 3.3-inch pulley and retuning the calibration. You'll need at least 500cc injectors, and you can use RC injectors if you don't mind soldering.

260 whp is nice, but I still want more.

The 3.3-inch pulley will make about 275+ whp (for that you either need injectors modified by Comptech, or RC 550 or 650 injectors if you don't mind cutting and crimping wires), and Comptech will release an aftercooler kit that will probably add another 15 whp or so. Also, special SC cams, race headers, etc., can push the performance level even higher.

Can I use the larger K24 crank pulley for more boost?
The k24 pulley will increase boost by one or two psi, but according to one tester, there is a danger that the groove in the crankshaft for the key is starting to wear to one side. We recommend against using the k24 pulley.

I want to break into the 12s. Can I do that with the CTSC?

Yes, OsideJimc ran a 12.96 in the quarter with a 9-psi CTSC on Hoosiers, and even faster with a 10-psi configuration that used race gas and IPS cams.

Can my engine handle high boost?

The k20 series is a strong engine, but experts suggest not to go past about 9.5 psi on stock pistons as the ring lands can't handle prolonged stress. Joe McCarthy at prototyperacing.com recommends CP and JE boost pistons and Carrillo, Cunningham or Crower rods. He says, "Don't use anything made in China, like Eagle, Scat, or Import Builders; it's false economy putting cheap rods into an engine."

How do I replace the blower pulley?

Remove the outer portion of the belt tensioner. Then move the power steering reservoir out of the way (remove two bolts). Use a 12-inch crescent wrench to hold the blower pulley and an 18-mm socket to remove the pulley nut.

If a belt breaks, how do I replace it? (thank you, OsideJim!)

1. Release tension using 12mm socket
2. Pop P/S resivoir out of bracket
3. Remove 2x 12mm bolts holding tensioner in place, remove tensioner
4. Using 14mm wrench remove bracket holding fixed idler
5. Jack up right front of car, remove tire, then remove 2 plastic clips holding splash guard in place.
6. Remove belt, feed new belt from above, then route around pulleys starting from below (see step 30 of install instructions for details Install Instructions (http://www.comptechusa.com/instructi...harger2005.pdf) ).
7. Re-install fixed idler, being careful to route belt properly.
8. Re-install tensioner arm but do not completely tighten bolts, make sure lip on brass thingie on the end of the tensioner is hooked on bottom of fixed idler barcket, adjust tension, then finish tightening tensioner mounting bolts.
9. Double check belt routing and installation then re-install splash guard and wheel.
10. Drive it 50 miles and re-adjust tension.
11. Repeat step 10

Click for belt routing picture

Have there been problems with the CTSC?

Comptech's initial tensioner design was prone to breaking, so Comptech designed a new one and sent a new tensioner/pulley kit, free of charge, to all owners (if you didn't get one, call Comptech with blower serial number). There have also been a number of cases where the pulley sheared off the blower assembly. Comptech redesigned the compressor snout and is replacing it on all units. Further, installation requires bending the powersteering line a bit, and that has caused some breaks.

I heard the CTSC, if installed by Acura, will not void my warranty.

Officially, Comptech's warranty only covers the base Comptech Supercharger kit, but no engine or other failures that might possibly have been caused by the CTSC. However, Comptech and Acura dealers have been known to be very accommodating in working with customers on such cases.

How does it feel to drive with the CTSC?

Wonderful. Around town a street CTSC car idles and drives just like stock. But when you step on it, there is much more power and torque. In fact, you can no longer floor the accelerator in 1st gear as you get wheel spin and hop, and there is enough power for wheel spin in second. Bottomline: a CTSC is much faster than stock, but launching it will require a new technique. Stickier tires might help a lot.

I don't see a CTSC calibration for the K-Pro.

Hondata created the k-100 calibration for the CTSC on Comptech's dyno. However, in order not to jeopardize the CARB approval process, Comptech cannot release that calibration. Those who already have the K-Pro and want the CTSC should simply use the JRSC calibration. The two systems are similar.

Can I buy the CTSC from ClubRSX?
Yes, on June 30, 2005, ClubRSX became an official Comptech dealer. When you make your purchasing decision, consider how much free support and information on the CTSC you get here on the ClubRSX forums.

Created: April 26, 2005 by conradb212
Last updated: September 15, 2005
Attached Thumbnails
Click image for larger version

Name:	CTSC_CARB_small.jpg
Views:	24438
Size:	53.1 KB
ID:	218338  
__________________
Mods: Stage 3 Comptech SC, AEM CAI, Comptech street header, stock cat, modified stock injectors, Hondata K-Pro, Hondata IMG, Fujitsubo PG catback, cat, 225/45-17 Goodrich G-force Rivals on Kazera rims, Mugen SS, Quaife LSD, CT lightweight flywheel and street clutch, ACT heavy-duty pressure plate, CT rear sway/tie bar and titanium front strut brace, Type-R replica wing, CT short shifter, Auto Meter Sport Comp full-sweep boost gauge. Current results: 290 whp on DynaPack. Web: My RSX and K-Pro page. My Blog: ECU Tuning

Last edited by conradb212; 01-29-2006 at 10:40 PM..
conradb212 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 04-26-2005, 02:50 PM   #2
DavidIX
If ur not 1st ur last
 
Join Date: Jun 2004
Posts: 6,854
iTrader: (2)
DavidIX is an unknown quantity on c-rsx
5 star sticky.
DavidIX is offline   Reply With Quote
Old 04-26-2005, 03:43 PM   #3
krystar
Master Member
 
krystar's Avatar
 
Join Date: May 2003
Location: Darien/Chicago
Posts: 24,670
iTrader: (9)
krystar is an unknown quantity on c-rsx
yay for new FAQ
__________________
Quote:
Originally Posted by DJCarbine
I have a 6 sheets of paper in front of me, all of them my fuel maps. I'm noting where to add and take away fuel.
This is the most work I've done at work EVER
krystar is offline   Reply With Quote
 
Old 04-26-2005, 03:59 PM   #4
imyy4u
2006 mustang GT 5spd
 
Join Date: Oct 2004
Location: south side of chicago
Posts: 1,571
iTrader: (0)
imyy4u has been a little shit in the past
excellent FAQ, should be stickied and locked though.
__________________
2006 black ford mustang gt coupe 5spd
3.55 rear axle, IUP, shaker1000 system, 300hp/320tq

2003 s/c debadged pwp rsx-s
stock header, stock exhaust, 265whp/186wtq @ 7psi
SOLD 7/25/06
imyy4u is offline   Reply With Quote
Old 04-26-2005, 09:16 PM   #5
conradb212
ECU Tuner
 
conradb212's Avatar
 
Join Date: Nov 2003
Location: Farragut, TN
Posts: 4,281
iTrader: (0)
conradb212 is an unknown quantity on c-rsx
Quote:
Originally Posted by imyy4u
excellent FAQ, should be stickied and locked though.
That's what I wrote this FAQ for. I asked our moderator, Randeezle, to unsticky the huge Comptech thread and sticky this one instead. The big thread made sense as I was reporting on the development of the Comptech kit, but now most of what is discussed in the CTSC thread is general SC issues, and newcomers have a hard time finding anything in such a long thread.
__________________
Mods: Stage 3 Comptech SC, AEM CAI, Comptech street header, stock cat, modified stock injectors, Hondata K-Pro, Hondata IMG, Fujitsubo PG catback, cat, 225/45-17 Goodrich G-force Rivals on Kazera rims, Mugen SS, Quaife LSD, CT lightweight flywheel and street clutch, ACT heavy-duty pressure plate, CT rear sway/tie bar and titanium front strut brace, Type-R replica wing, CT short shifter, Auto Meter Sport Comp full-sweep boost gauge. Current results: 290 whp on DynaPack. Web: My RSX and K-Pro page. My Blog: ECU Tuning
conradb212 is offline   Reply With Quote
Old 04-26-2005, 11:53 PM   #6
ACTypeS
k20a type s
 
Join Date: Aug 2004
Posts: 532
iTrader: (0)
ACTypeS is an unknown quantity on c-rsx
Good thinking conrad, that thread was ridiculously too long....
__________________
Need an install in the Northeast? (Jersey)
Alarms - remote starts - systems - tv's - custom fiberglassing - anything 12v... PM, email, AIM for details...

"God created toilet paper to take some of the shit off of our hands..."[/SIZE]
ACTypeS is offline   Reply With Quote
Old 04-28-2005, 09:01 AM   #7
Special Ed
What The Problem Is?
 
Special Ed's Avatar
 
Join Date: Nov 2002
Location: Evanston, IL
Posts: 9,176
iTrader: (1)
Special Ed is an unknown quantity on c-rsx
Great post.
__________________
Rate it @ http://www.cardomain.com/ride/1021356

Motorcycle crew #007 Biiioootttccchhh! Cruiser style! 06 HD Night Train
Special Ed is offline   Reply With Quote
Old 04-28-2005, 04:51 PM   #8
Oside Jimc
RIP 2/4/2009
 
Oside Jimc's Avatar
 
Join Date: Aug 2004
Location: SoCal
Posts: 4,736
iTrader: (11)
Oside Jimc is an unknown quantity on c-rsx
Replacement belt (As of 4/28/05) Goodyear # 4070775

Edit: This is only for the 3.3" pulley (not sure about 3.6" pulley) when using the new tensioner assembly. The 3.8" pulley requires Comptech's custom 78.5" belt.
__________________
The liver is evil, it must be punished

Last edited by Oside Jimc; 06-27-2005 at 11:41 AM..
Oside Jimc is offline   Reply With Quote
Old 05-20-2005, 01:06 AM   #9
NWRSX
Senior Member
 
NWRSX's Avatar
 
Join Date: Jan 2003
Location: Westminster, CO
Posts: 426
iTrader: (0)
NWRSX is an unknown quantity on c-rsx
Comptech part #s for:
Replacement belt 357-002
3.6" Pulley 357-209
3.3" Pulley 357-212
Stage 2 Upgrade Kit 350-031

Last edited by NWRSX; 06-10-2005 at 10:33 PM..
NWRSX is offline   Reply With Quote
Old 06-12-2005, 09:45 AM   #10
munlit
Immortal Ueshiba Morihei
 
munlit's Avatar
 
Join Date: Jan 2003
Location: NYJ
Posts: 2,961
iTrader: (2)
munlit is an unknown quantity on c-rsx
any updates?
__________________
FS: mugen replica bumper, CTSC NIB $3200 for Type-S, stoptech stage II kit, spoonstrut bar,leather rear seat plus recaro blue fabric ,pm me for prices
FALL SALE ---> http://forums.clubrsx.com/showthread.php?t=739066
munlit is offline   Reply With Quote
Old 06-13-2005, 11:56 PM   #11
DC5_Angelo
Master Member
 
DC5_Angelo's Avatar
 
Join Date: Mar 2005
Location: saint johns
Posts: 1,793
iTrader: (8)
DC5_Angelo is an unknown quantity on c-rsx
any????
__________________
2002 RSX


Quote:
Also no matter how fast an SRT-4 is, it can't outrun UGLY.
DC5_Angelo is offline   Reply With Quote
Old 06-14-2005, 12:06 AM   #12
krystar
Master Member
 
krystar's Avatar
 
Join Date: May 2003
Location: Darien/Chicago
Posts: 24,670
iTrader: (9)
krystar is an unknown quantity on c-rsx
are u looking for something specific? this is a FAQ thread.
__________________
Quote:
Originally Posted by DJCarbine
I have a 6 sheets of paper in front of me, all of them my fuel maps. I'm noting where to add and take away fuel.
This is the most work I've done at work EVER
krystar is offline   Reply With Quote
Old 06-22-2005, 10:47 PM   #13
HeX
Member
 
HeX's Avatar
 
Join Date: Aug 2004
Location: New Jersey
Posts: 70
iTrader: (0)
HeX is an unknown quantity on c-rsx
i have a base, so if were to get k-pro and the base CTSC i would just have to use JRSCs calibration? would that keep it CARB legal or no?
HeX is offline   Reply With Quote
Old 06-22-2005, 11:01 PM   #14
krystar
Master Member
 
krystar's Avatar
 
Join Date: May 2003
Location: Darien/Chicago
Posts: 24,670
iTrader: (9)
krystar is an unknown quantity on c-rsx
u don't need to worry about CARB legal. carb only applies in california. u just have to worry about new jersey's emissions laws.
__________________
Quote:
Originally Posted by DJCarbine
I have a 6 sheets of paper in front of me, all of them my fuel maps. I'm noting where to add and take away fuel.
This is the most work I've done at work EVER
krystar is offline   Reply With Quote
Old 06-23-2005, 12:49 AM   #15
HeX
Member
 
HeX's Avatar
 
Join Date: Aug 2004
Location: New Jersey
Posts: 70
iTrader: (0)
HeX is an unknown quantity on c-rsx
yeah, but i can't find anything on them from the clean air website, and also, why doesn't comptech list the base supercharger on their website?
HeX is offline   Reply With Quote
Old 06-23-2005, 01:01 AM   #16
Seanwins
Who's the big winner????
 
Seanwins's Avatar
 
Join Date: Feb 2004
Location: Seattle
Posts: 1,246
iTrader: (1)
Seanwins is an unknown quantity on c-rsx
It hasnt been released yet I think

Check the Comptech Base Supercharger thread

http://67.15.94.66/showthread.php?t=...ercharger+Base
Seanwins is offline   Reply With Quote
Old 06-26-2005, 12:00 AM   #17
drunkenpanda
?
 
drunkenpanda's Avatar
 
Join Date: Apr 2004
Location: CALI
Posts: 3,533
iTrader: (2)
drunkenpanda is an unknown quantity on c-rsx
wow good write up
__________________
2004 Nighthawk Black Pearl RSX Type S
Pharmacy school Statistics
drunkenpanda is offline   Reply With Quote
Old 07-16-2005, 01:04 PM   #18
Seanwins
Who's the big winner????
 
Seanwins's Avatar
 
Join Date: Feb 2004
Location: Seattle
Posts: 1,246
iTrader: (1)
Seanwins is an unknown quantity on c-rsx
Some good info with illustrations of how a boost bypass valve works.

http://www.timskelton.com/lightning/...ost_bypass.htm
Seanwins is offline   Reply With Quote
Old 07-23-2005, 07:17 PM   #19
dboyzalter
Dirtboydel
 
dboyzalter's Avatar
 
Join Date: Feb 2004
Location: Masshole
Posts: 1,876
iTrader: (0)
dboyzalter is going down hard
love the sticky +1 for you
dboyzalter is offline   Reply With Quote
Old 09-17-2005, 07:29 PM   #20
definitions
RSXology
 
definitions's Avatar
 
Join Date: Jan 2004
Location: G.T.A
Posts: 707
iTrader: (3)
definitions is an unknown quantity on c-rsx
i know that hondata hasnt release a flash or k-pro without using the adapter yet. does that mean i cant get the CTSC yet? i really want to go supercharged!
__________________
RSX TypeS MM
definitions is offline   Reply With Quote
Old 09-18-2005, 09:52 AM   #21
tryfe
Master Member
 
tryfe's Avatar
 
Join Date: Sep 2003
Location: CT
Posts: 13,797
iTrader: (11)
tryfe is on a distinguished road tryfe is on a distinguished road
Quote:
Originally Posted by definitions
i know that hondata hasnt release a flash or k-pro without using the adapter yet. does that mean i cant get the CTSC yet? i really want to go supercharged!
You can't get it yet then.
__________________
2005 wrb wrx | 01/16/08 -
2002 ssm rsx-s | 06/24/03 - 11/23/07

"has anyone really been far even as decided to use even go want to do look more like?"
tryfe is offline   Reply With Quote
Old 11-02-2005, 04:56 PM   #22
joejoe3
Supercharged Crew #37
 
joejoe3's Avatar
 
Join Date: Aug 2003
Location: Calgary, Alberta
Posts: 1,350
iTrader: (4)
joejoe3 is an unknown quantity on c-rsx
Question on the injectors.
If I plan to start off in stage 2 and gradually go up the boost level, would it hurt to get 6xxcc injectors right off the bat?
joejoe3 is offline   Reply With Quote
Old 11-02-2005, 07:54 PM   #23
krystar
Master Member
 
krystar's Avatar
 
Join Date: May 2003
Location: Darien/Chicago
Posts: 24,670
iTrader: (9)
krystar is an unknown quantity on c-rsx
as long as you got kpro, go whatever

550 work up to 9psi just dandy. but if you're going other things, then get bigger
__________________
Quote:
Originally Posted by DJCarbine
I have a 6 sheets of paper in front of me, all of them my fuel maps. I'm noting where to add and take away fuel.
This is the most work I've done at work EVER
krystar is offline   Reply With Quote
Old 11-03-2005, 03:41 PM   #24
joejoe3
Supercharged Crew #37
 
joejoe3's Avatar
 
Join Date: Aug 2003
Location: Calgary, Alberta
Posts: 1,350
iTrader: (4)
joejoe3 is an unknown quantity on c-rsx
There was another thing i was gonna ask, that i think should go on the FAQ.
As we know, comptech supplies a reflash for their SC. Either it be the K100 supplied or reflashing your Kpro. On their website, it says that you can still maintain the datalogging.

But there was something about it, that you cannot re-map unless the supplied SC map has been deleted.
"Comptech ECU Map is locked, and must be deleted in order to make any changes"

What’s the whole point of it then? If there was knocking or A/F issues and you see it in your datalog, but you can’t fix it anyway!? Doesn’t that defeat the whole purpose of “programmable” ECU?

Last edited by joejoe3; 11-03-2005 at 03:46 PM..
joejoe3 is offline   Reply With Quote
Old 11-03-2005, 04:46 PM   #25
conradb212
ECU Tuner
 
conradb212's Avatar
 
Join Date: Nov 2003
Location: Farragut, TN
Posts: 4,281
iTrader: (0)
conradb212 is an unknown quantity on c-rsx
Quote:
Originally Posted by joejoe3
There was another thing i was gonna ask, that i think should go on the FAQ.
As we know, comptech supplies a reflash for their SC. Either it be the K100 supplied or reflashing your Kpro. On their website, it says that you can still maintain the datalogging.

But there was something about it, that you cannot re-map unless the supplied SC map has been deleted.
"Comptech ECU Map is locked, and must be deleted in order to make any changes"

What’s the whole point of it then? If there was knocking or A/F issues and you see it in your datalog, but you can’t fix it anyway!? Doesn’t that defeat the whole purpose of “programmable” ECU?
Well, if you have K-Pro and their locked map you can datalog. The data will give you lots of information and teach you a bunch about your engine and how it runs. However, you can't change the Comptech map. You are, however, free to clear the map and upload one of the many available SC calibrations. They all work well as starting points and often provide more power (because the locked Comptech must, by definition, be a "one size fits all").
__________________
Mods: Stage 3 Comptech SC, AEM CAI, Comptech street header, stock cat, modified stock injectors, Hondata K-Pro, Hondata IMG, Fujitsubo PG catback, cat, 225/45-17 Goodrich G-force Rivals on Kazera rims, Mugen SS, Quaife LSD, CT lightweight flywheel and street clutch, ACT heavy-duty pressure plate, CT rear sway/tie bar and titanium front strut brace, Type-R replica wing, CT short shifter, Auto Meter Sport Comp full-sweep boost gauge. Current results: 290 whp on DynaPack. Web: My RSX and K-Pro page. My Blog: ECU Tuning
conradb212 is offline   Reply With Quote
Reply

Bookmarks

Tags
comptech , faq , supercharger

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:41 AM.


Privacy Policy  |  Disclaimer Notice
Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright © 2001-2012, Club RSX, Inc. All rights reserved worldwide.
This website is owned and operated by Club RSX, Inc.
Club RSX, Club EP3, and Club ILX are not affiliated with American Honda Motor Co., Inc.